|
Content
Operation
General information
Description of models
Vehicle specifications
Identification numbers of the car and engine
Equipment
Car keys
Doors
Hood
Boot lid
Fuel tank plug
Seats
Seat belts
Steering wheel adjustment
Mirrors
Central interior light
Individual lighting
Sun visors
Storage boxes
Controls and instruments
Dashboard
Key switches
Adjustable steering column
Instrument cluster
Gearshift paddles
Ignition switch
On-board control system
Trip computer
Heating and ventilation
Service
Safety precautions for maintenance and repair
Maintenance
Location of the main units of the car
Checking the car before leaving
Maintenance schedule
Replacing the air filter
Replacing the fuel filter
Changing the engine oil
Replacing spark plugs
Coolant replacement
Checking the tension and replacing the alternator drive belt
Adjustment of thermal clearances in the timing gear drive
Checking the tension and replacing the timing belt
Gearbox oil change
Front wheel alignment
Replacing the front brake pads
Replacing the rear brake pads
Parking brake adjustment
Brake fluid change
Clutch adjustment
Checking and adjusting the steering gear
Headlight adjustment
Headlight adjustment
Fog light adjustment
battery maintenance
Engine
Design description
Replacing the camshaft oil seal
camshaft removal
Replacing valve stem seals
Replacing the front crankshaft oil seal
Replacing the crankshaft rear oil seal
Removing the oil pressure warning lamp sensor
Removing low oil sensor
Removing the receiver and collectors
Removing and disassembling the cylinder head
Removing the oil pan
Removing the oil receiver
Removing and disassembling the oil pump
Dismantling the connecting rod and piston group (SHP) without removing the engine from the car
Removing the rear support of the power unit
Removing the left support of the power unit
Removing the front support of the power unit
Removing the engine from the car
Dismantling and assembling the engine
Power system
Design description
Checking the pressure in the fuel system of the engine
Removing the fuel vapor separator
Removing the fuel tank
Removing the gasoline pump with a fuel level sensor
Removing the fuel pressure regulator
Removing the fuel rail
Removing engine injectors
Checking engine injectors
Removing the throttle actuator
Throttle removal
Removing the idle speed regulator
Removing the air filter housing
Engine management system
Injection system controller (control unit)
Injection sensors
Crankshaft position sensor
Coolant temperature sensor
Throttle position sensor (TPS)
Mass air flow sensor
Knock Sensor
Oxygen concentration sensor (oxygen sensor, lambda probe)
Vehicle speed ??sensor
Idle control
Ignition system
Engine control fuses and relays
The operation of the injection system
Removing the diagnostic pads
Replacing injection relays and fuses
Removing the control unit and the status indicator of the automobile anti-theft system (APS)
Removing the controller
Removing the crankshaft position sensor
Removing the coolant temperature sensor
Removing the throttle position sensor
Removing the mass air flow sensor
Removing the knock sensor
Removing the oxygen sensor
Removing the speed sensor
Removing the ignition module
Cooling system
Design description
Removing coolant temperature sensor for instrument cluster
Removing and checking the thermostat
Removing the expansion tank
Removing the electric fan
Removing the radiator
Removing the coolant pump
Exhaust system
Design description
Front pipe removal
Removing the optional silencer
Neutralizer removal
Removing the main silencer
Grip
Design description
Clutch cable removal
Replacing drive plate and clutch cover
Removing clutch release mechanisms
Gearbox
Design description
Removing the gearshift drive
Gearbox removal
Replacing gearbox oil seals
Gearbox disassembly and assembly
Front wheel drive
Design description
Removing front wheel drives
Removing the outer joint
Removing and disassembling the inner joint
Front suspension
Design description
Removing the ball joint
Removing the lever, brace and bracket
Removing the shock absorber strut and its disassembly
Removing the anti-roll bar
Replacing the front wheel bearing
Rear suspension
Design description
Removing the shock absorber and spring
Replacing the silent blocks of the rear suspension beam
Removing the rear suspension beam
Replacing the hub bearing
Steering
Design description
Steering wheel removal
Steering column removal
Removing the tie rod end
Removing and disassembling the steering gear
Brake system
Design description
Bleeding the brakes
Removing the brake master cylinder
Removing the vacuum booster and adjusting the brake pedal free play
Removing the front brake hose
Removing front wheel brake parts
Replacing the rear brake cylinder
Removing the rear brake hose
Checking and adjusting the rear brake pressure regulator actuator
Removing the rear brake pressure regulator
Removing the parking brake components
Electrical equipment
Design description
Replacing fuses and relays
Removing the mounting block
Removing the ignition switch
Ignition relay removal
Battery
Generator
Generator test
Removing and disassembling the generator
Starter
Starter removal
Dismantling of a starter 5712.3708
Dismantling the starter 29.3708
Lighting and light alarm
Headlights
Removing the headlight, replacing the lamps
Headlight hydrocorrector
Removing the headlight fluid corrector
Fog lights
Removing the direction indicator, replacing the lamp
Removing the side direction indicator, replacing the lamp
Replacing the reversing light switch
Removing taillights, replacing bulbs
Removing the rear fog lamp relay
Removing an additional brake signal
Removing the rear license plate light, replacing the lamp
Removing the engine compartment lamp holder, replacing the lamp
Removing the central interior light and replacing the lamp
Removing the front interior light
Removing the plafond and the lower glove box lighting switch
Removing the steering column switch
Removing the alarm switch
Sound signal
Beeping
Cigarette lighter removal
Rear window heating system (rear door glass)
Window cleaners and washers
Removing and disassembling the windshield wiper
Removing the liquid level sensor and the washer electric pump
Rear door wiper and washer
Removing the tailgate wiper motor gearbox
Engine cooling fan motor
Monitoring devices and signaling devices
Checking control devices and their sensors
Removing instrument cluster and light switch
Removing the alarm block
Body
Design description
Outside rearview mirror
Interior rearview mirror
Removing the sun visor
Ceiling handrail
Facing the tunnel floor
Carpeted floor and soundproofing material
Removing the shelf under the rear window
Roof upholstery
Removing the front seat belt
Removing the front seat and slide
Removing the rear seat
Removing the dashboard
Removing the inner radiator lining
Removing the outer radiator lining
Removing the headlamp trim
Front bumper with aluminum beam
Front bumper with plastic energy absorbing element
Rear bumper with aluminum beam
Rear bumper with plastic energy absorbing element
Fairing removal
Removing the hood lock, lock drive and safety hook
Hood
Mudguard engine
Front fender liner removal
Front wing
Replacing the windshield
Replacing an external door lock
Removing the door trim
Removing the door lock
Removing the door glass
Removing the power window mechanism
Spoiler removal
Removing the tailgate trim
Removing the tailgate lock
Removing the tailgate
Removing the tailgate lock
Removing the boot lid
Heating and ventilation system
Design description
Heater tap removal
Heater fan removal
Removing the rear air ducts
Removing the instrument panel ducts
Removing the heater radiator
Removing and disassembling the heater
Diagnostics of malfunctions
Tuning recommendations
Applications
A tool used in addition to the staffing
Applicable fuels, lubricants and operating fluids
Tightening torques for threaded connections
Basic data for adjustments and control
Lip seals (glands)
Rolling bearings
Lamps used in the car
Electrical equipment schemes |
Translation Techniques. English - Russian. Практические основы перевода
Автор: Т. А. Казакова
Год издания:
