|
This book provides only a description of the repair of the engine SOCH / DOCH
To get acquainted and to buy the full book on car repair Subaru Legacy / Subaru Forester / Subaru Outback / Subaru Baja since 2000 (including engine) it is possible under the link
Content
Engines
General information
Repair operations carried out without removing the engine
Top dead center (TDC) of the piston of the first cylinder - location
Valve covers - removal and installation
Intake manifold - removal and installation
Exhaust manifold - removal and installation
Toothed belt and sprockets - removal, inspection and installation
Systems for adjusting the phases of the gas distribution mechanism and valve capacity
Front crankshaft oil seal - replacement
Camshaft seals - replacement
Camshafts and valve train parts - removal, inspection and installation
Cylinder heads - removal and installation
Valve clearances - checking and adjusting
Pallet - removal and installation
Oil pump - removal, inspection and installation
Flywheel / drive plate - removal and installation
Engine rear main oil seal - replacement
Engine mounts - inspection and replacement
Engine overhaul
General information - engine overhaul
Oil pressure test
Checking compression in engine cylinders
Diagnosis with underpressure measurement
Alternative engine recovery methods
Engine removal - methods and precautions
Engine - removal and installation
Engine overhaul - disassembly sequence
Pistons - removal and installation
Carter - Branch
Crankshaft and connecting rods - removal
Connecting rods and bearings - removal
Engine overhaul - assembly sequence
Connecting rods and bearings - installing and checking oil clearance
Crankshaft and main bearings - installing and checking oil clearance
Carter - assembly
Piston rings - installation
Pistons - installation
The first start and running-in of the engine after a major overhaul
Fuel and exhaust system
General information
Depressurizing the fuel system
Fuel pump / fuel pressure - check
Fuel lines and their connectors - replacement
Fuel pump / fuel level sensor - removal and installation
Fuel pump / measuring unit / fuel filter - replacement
Separate fuel system gauge block - removal and installation
Fuel tank - removal and installation
Fuel tank cleaning and refurbishment - general
Air cleaner - removal and installation
Accelerator cable - removal and installation
Multipoint Fuel Injection (MFI) - General
Fuel injection system - general condition check
Throttle block - removal and installation
Fuel pressure regulator - removal and installation
Fuel receiver and injectors - removal and installation
Turbocharger - description and inspection technique
Air bypass valve - removal and installation
Intercooler - removal and installation
Turbocharger - removal and installation
Exhaust system maintenance - general
Exhaust gas composition monitoring and engine management
General information
On-Board diagnostic (OBD) and trouble codes (DTC)
Accelerator pedal position sensor (APP) - replacement
Barometric pressure sensor (BARO) - replacement
Camshaft position sensor (CMP) - replacement
Clutch pedal position sensor (CPP) - replacement
Crankshaft position sensor (CKP) - replacement
Coolant temperature sensor (ECT) - replacement
Exhaust temperature sensor - replacement
Supply air temperature (IAT) sensor - replacement
Intake air temperature (IAT)/manifold absolute pressure sensor - replacement
Knock sensor - replacement
Manifold absolute pressure (MAP) sensor - replacement
Air meter/supply air temperature sensor (MAF/IAT) - replacement
Oxygen sensors - general information and replacement
Power steering (PSP) hydraulic pressure sensor - replacement
Throttle position sensor (TP) - replacement
Selector lever position sensor (TR) - replacement and adjustment
Vehicle Speed ??Sensor (VSS) - replacement
Engine Control Module (PCM) - replacement
Solenoid valve system have additional air injection – replacement
Idle air valve (IAC) - replacement
Catalytic converters - description and replacement of elements
EVAP system - general description and replacement of elements
Exhaust gas recirculation (EGR) system - general description and replacement of elements
Crankcase ventilation (PCV) system - general description and replacement of elements
Auxiliary air injection system - general description and replacement of elements
The device for swirling the air-fuel mixture when starting the engine - a general description and replacement of elements
Valve lift change system - general description and replacement of elements
Valve timing correction system - general description and replacement of elements |
Translation Techniques. English - Russian. Практические основы перевода
Автор: Т. А. Казакова
Год издания:
Subaru B9 Tribeca с 2005 по 2007 год, книга по ремонту в электронном виде
Автор: Монолит
Год издания:
