
Автор: Диез
Год издания: 0000
The second volume provides information on repairs:
- cooling systems
- fuel system;
- clutch and gearbox;
- brake system.
Content
Cooling system
General information
Radiator
Coolant bypass
Circulation in the engine 12 l
Circulation in the engine 14 l
Expansion tank
Level indicator
Thermostat
Coolant filter
Cooling pump
Cooling system maintenance
Adding coolant
High coolant temperature
Low coolant temperature
Coolant leak
Cooling system cleaning - interior
Radiator (P and R cabs with plastic bumper)
Removing the radiator
Installing a radiator
Radiator (P and R cabs with metal bumpers)
Removing the radiator
Installing a radiator
Radiator (T cab)
Removing the radiator
Radiator replacement
Installing a radiator
Expansion tank
Pressure limiting valve
Fan
Withdrawal
Installation
Checking fan operation
Thermostat
Coolant filter
Coolant pump
Withdrawal
Installation
Inspection
Pulley
Oil seal
Installation
Checking the thermostat operation
Belt drive
Fuel equipment
Fuel filter
Replacement
Fuel filter with water separation
Additional fuel filter with water separation
Distribution tube
Feed pump
Measuring the pressure of the feed pump
Single-acting feed pump
Double-acting feed pump
Bypass valve
Fuel valve
Injectors
Injection pump
Replacing the pump on DSC9 and 11 engines
Replacing the pump on the DSC12 engine
Replacing the pump on the DSC14 engine
Injection adjustment on DSC 9, 11 and 12 engine
Injection adjustment on the DSC 14 engine
Overflow injection control
Unit injectors
Fuel system service
Bleeding the fuel system
Replacing the feed pump
Replacing the wires of the unit injectors
Replacing wires on a free panel
Replacing the control unit
Connecting special functions for the engine
Fuel heater
Fuel heater installation
Heater connection diagrams
All-speed regulator RQV
Idling and maximum speed regulator RQ
Smoke limiter
Starting the engine with preheating
Elements of the engine preheating system
Troubleshooting
Testing
Preheat starting engine connection diagram
Clutch
Removing the gearbox
Replacing the clutch slave cylinder
Checking the spring diaphragm
Checking the pressure plate
Installing the clutch
Installing the gearbox
Servo replacement
Draining the hydraulic system
Clutch K432 15, K432 16, K432 17, K432 18
Gearbox
Withdrawal
Installation
Gearbox GR801 / 900, GRS890 / 900
Control scheme
Overexcitation protection
Neutral valve
Isolation Valve, Divider Gear
Control valve, separator / row
Row wiring diagram, troubleshooting
Checking the circuit of the solenoid valve in the control valve next
Checking the engine speed sensor circuit
Checking the E8 overexcitation protection device
Power check
Row switch test
Divider wiring diagram, troubleshooting
Power check
Checking the separator switch
Checking the circuit of the solenoid valve in the split control valve
Checking the clutch switch
Checking the circuit of the solenoid valve in the isolating valve
Row air circuit, troubleshooting
Neutral valve
Row control valve
Split isolation valve, air circuit GRS890 / 900
Separation control valve
Gearbox GR 900
Lubrication system
Gear shifting
Transmission of torque in different gears in the main gearbox
Power takeoff
Synchronizers
Cruise control, hall sensor, adjustment and replacement
Replacing the longitudinal cylinder
Replacing the side stroke cylinder
Axial clearance
Filling volumes
Gearbox GR801
Torque booster KH 424 3
Torque converter
Torque boost
Locking clutch
Braking system
Air flow diagram
Location of brake system components
Complete diagram of air lines of SCANIA 4 series cars
Explanation of designations on the diagram of air lines
Front brake circuit
Supply section supplying compressed air to the single wheel front axle
Supply section that supplies air to the two front axles
Executive part of the front brake circuit, front axle with single wheels
Front contour diagram, front axle with single wheels
Front contour diagram, two front axles
Executive part, cars with two front axles
Rear brake circuit
Power supply
Executive part, single rear axle with leaf spring or air suspension
Executive part, bogie of additional (non-driving) rear axle. with air suspension and 4-channel ABS
Executive part, bogie of additional rear axle. with leaf spring suspension and 4-channel ABS
Executive part, double trolley. with leaf spring suspension and 4-channel ABS
Executive part, bogie of additional rear axle and double bogie. with air suspension and 6-channel ABS
Executive part, three-row trolley. with additional steering axle
Rear brake circuit diagram, bogie of additional rear axle. with air suspension and 4-channel ABS
Rear brake circuit diagram, single rear axle. with leaf spring or air suspension
Rear brake circuit diagram, bogie of additional rear axle. with leaf spring suspension and 4-channel ABS
Rear brake circuit diagram, double bogie. with leaf spring suspension and 4-channel ABS
Rear brake circuit diagram, rear axle bogie and tandem bogie. with leaf spring suspension and 6-channel ABS
Rear brake circuit diagram, three-axle bogie with air suspension. and an additional rear axle in front of the driving axle (wheel arrangement 8x2 / 4)
Rear brake circuit diagram, three-axle bogie. with air suspension and an additional rear axle behind the driving axle (wheel arrangement 8x4 * 4)
Parking brake circuit
Compressed air supply
Executive part
Parking brake control procedure
Secondary brake position
Parking brake position
Check position
Trailer braking circuit
Additional equipment outline
Trailer outline diagram
Parking brake circuit diagram
Compressed air supply system
System components
Compressor
Air dryer
Four-way safety valve
Safety valve (safety)
Bypass valve
Compressor
Withdrawal
Dismantling the cylinder head
Cylinder head cleaning and assembly
Compressor troubleshooting
Installation
Air dryer
Withdrawal
Replacing the desiccant cartridge
Valve body replacement
Check valve replacement
Air dryer installation
Pressure relief test
Bypass valve
Disassembly
Cleaning and checking
Build
Installation
Specifications
Details of the front and rear brake circuit
Service brake valve
Pressure regulator valve (responsive to the weight of the machine load)
Pressure regulating valve type I, for trucks with leaf spring suspension
Pressure regulator valve type II, for trucks with air suspension
Safety valve
Booster valve
Pressure gauge / indicator
Service brake valve
Pressure regulator valve for trucks with leaf spring suspension
Pressure regulator valve for air suspension trucks
Installing a pressure regulator valve
Booster valve
Parking brake. Main nodes
Manual directional valve
Directional valves types I and II with test positions
WABCO type I and III control valves
Emergency braking
Emergency braking / parking brake position
Test position, type I control valve only
Actuator position type II and IV directional valves (KNORR)
Emergency braking with directional valves type II and IV, parking position with valve type II
Type IV directional valve without test position
Test position, only for type II control valve
Manual control valve operation diagram
Block valve
Parking brake accelerator valve
Pressure limiting valve
Low pressure indicator
Double check valve
Quick release valve
Disengaging the parking brake
Applying the parking brake
Components used to disengage the parking brake when using the second generation electronic air suspension control (ELC2)
Back-up brake valve
Removal and installation of main units
Symbols of elements of the brake system on the diagrams
The principle of building a pneumatic circuit
Compressed air lines
Brake components
Components and parts of a wheel brake
Service brake chambers
How the service brake works
Checking the service brake
How the parking brake works
Disengaging the parking brake
Brake pad backlash adjuster
Manual gap adjustment
Automatic gap adjustment
Brake drums
Service brake chamber
Removing the spring brake chamber from the truck
Disconnecting the chamber spring assembly from the service brake assembly
Assembling the spring chamber and service brake chamber assemblies
Mechanism for manual clearance adjustment
Removing from the truck
Disassembly
Cleaning and checking
Installation on a truck
Measuring the basic setting of the pusher
Customization
Mechanism for automatic clearance adjustment
Measuring the basic setting of the pusher
Removing from the truck
Disassembly
Cleaning and checking
Build
Setting the spring force
Installing a slack adjuster on a truck
Customization
Removing the brake drum
Removing the brake pads
Brake cam rollers
Brake pads and friction linings
Brake drums
Specifications
Disc brakes
Removing wheels
Disc brake related components
Replacing brake pads
Brake caliper
Repair of brake calipers
Replacing the pilot pins, bushings and seals
Replacing the piston with oil seals
Spring brake chamber
Replacing the spring brake chamber
Diaphragm replacement
ABS / TC system
Friction
Slipping
Correlation between friction and skidding
ABS system
What happens while driving with the ABS system
TS system
ABS / TC system
Braking control
Engine management
Operation of the vehicle system in off-road conditions (TC OFF ROAD)
What happens during management
Wheel sensor
Control node design
Control node subsystems
ABS indicator lamps
Indicator lamp of the vehicle system
Control valve functions
Solenoid valve function
Double check valve function
Accelerating valve on a tractor with an additional rear non-driving axle
Installing the ABS system on other types of cars
Block diagram of the ABS / TC system of a 4x2 truck
4 and 6 channel WABCO ABS / TC systems (D versions)
Control unit
Reading fault codes
Troubleshooting
Electrical connections for wheel diagonals
Generating trouble codes
Electrical diagram
Component designation and resistance
Wiring diagrams
Layout of components
4-channel system diagrams
6-channel system diagrams
Braking system with EBS from BOSCH
System diagram
Troubleshooting
Flashing codes
Electrical components
Electrical diagrams
Reduction of brake pressure in the chain of the front wheels
Pressure relief valve 66a (V73)
E41 control unit
Signal lamp W31
Retarder brake (retarder)
Hydraulic part
Additional brake
Oil accumulator
Oil cooler
Proportional valve
How to work
When the auxiliary brake does not brake
When an additional brake is just made for braking
When the auxiliary brake is braking
When to increase the braking torque
When to reduce the braking torque
When to terminate the additional brake
Electrical part
Using the retarder
Braking (trucks with ABS)
Downhill speed control
Engine warm up (trucks with ABS)
Braking (trucks without ABS)
Warming up the engine (trucks without ABS)
Features of the brake system
Controls
ABS connections
Downhill speed control
Communication with EDC system
Engine braking exhaust throttling device
MBP signal output
Heated driver's cab and passenger compartment
Alert system
Reinstalling the alarm system
Retarder brake. Disassembly and assembly
Troubleshooting
Low braking effect
Critical details
External oil leak
Disassembly and assembly
Proportional valve
Oil cooler
Oil accumulator
Additional brake
Exhaust throttling device
Disassembly
Build
Adjustment
AD1100P wheel hub with RH730 reducer
Checking the oil level
Removing and installing a semiaxis
Removing the axle shaft
Removing the planetary gear
Replacing the planetary gear bearing
Replacing oil seals
Removing the hub
Antilock Brake System (ABS) impulse wheel replacement
Replacing wheel bearings
Installing the hub and pre-tightening the bearing
Installing the planetary gear
Semiaxis installation
Front axle disc brake hub

Автор: Mike Stabblefield
Год издания:
Руководство Haynes по обслуживанию и ремонту автомобиля Pontiac Fiero (1984-1988 гг.).

Автор: Николаенко Владимир Анатольевич
Год издания:
В данной книге на хорошем инженерном уровне, но в то же время просто и доступно, описаны модели ZAZ-DAEWOO SENS, с 2002 г. выпуска, торговое обозначение: T1311-01, T1311-02. Бензиновый двигатель с системой распределенного впрыска топлива:1. 3 л. - 51.

Автор: Т. А. Казакова
Год издания:
Учебное пособие предназначается изучающим английский язык и входит в систему предметов, обучающих теории и практике перевода. Материал пособия направлен на освоение и развитие практических навыков перевода с английского языка на русский и наоборот.Основным принципом построения пособия, отбора и расположения учебного материала является создание систематического представления о способах, средствах и приемах преобразования языковых единиц в процессе двустороннего перевода. Пособие может бытьиспользовано в рамках учебного процесса на факультетах иностранных языков, для обучения переводчиков, а также для самостоятельных занятий студентов, аспирантов, преподавателей английского языка и начинающих переводчиков.

Автор: Коллектив авторов
Год издания:
Инструкция по ремонту и обслуживанию моделей Fiat Tipo и Tempra. Дано описание всех узлов и агрегатов и советы по их эксплуатации и техобслуживанию. Чертежи, таблицы и схемы электрооборудования.
Fiat Tipo - автомобиль итальянской компании Фиат. Был разработан дизайн студией IDEA. Выпускался с 1988 года по 1996 год.

Автор: Galasso Sabrina, Trama Giuliana
Год издания:
Грамматические и лексические упражнения по итальянскому языку.