Найти книгу: "Lada / VAZ 2113 / 2114 / 2115 since 1997, service e-manual (in Russian)"

Content Operation General information Description of models Vehicle specifications Identification numbers of the car and engine Equipment Car keys Doors Hood Boot lid Fuel tank plug Seats Seat belts Steering wheel adjustment Mirrors Central interior light Individual lighting Sun visors Storage boxes Controls and instruments Dashboard Key switches Adjustable steering column Instrument cluster Gearshift paddles Ignition switch On-board control system Trip computer Heating and ventilation Service Safety precautions for maintenance and repair Maintenance Location of the main units of the car Checking the car before leaving Maintenance schedule Replacing the air filter Replacing the fuel filter Changing the engine oil Replacing spark plugs Coolant replacement Checking the tension and replacing the alternator drive belt Adjustment of thermal clearances in the timing gear drive Checking the tension and replacing the timing belt Gearbox oil change Front wheel alignment Replacing the front brake pads Replacing the rear brake pads Parking brake adjustment Brake fluid change Clutch adjustment Checking and adjusting the steering gear Headlight adjustment Headlight adjustment Fog light adjustment battery maintenance Engine Design description Replacing the camshaft oil seal camshaft removal Replacing valve stem seals Replacing the front crankshaft oil seal Replacing the crankshaft rear oil seal Removing the oil pressure warning lamp sensor Removing low oil sensor Removing the receiver and collectors Removing and disassembling the cylinder head Removing the oil pan Removing the oil receiver Removing and disassembling the oil pump Dismantling the connecting rod and piston group (SHP) without removing the engine from the car Removing the rear support of the power unit Removing the left support of the power unit Removing the front support of the power unit Removing the engine from the car Dismantling and assembling the engine Power system Design description Checking the pressure in the fuel system of the engine Removing the fuel vapor separator Removing the fuel tank Removing the gasoline pump with a fuel level sensor Removing the fuel pressure regulator Removing the fuel rail Removing engine injectors Checking engine injectors Removing the throttle actuator Throttle removal Removing the idle speed regulator Removing the air filter housing Engine management system Injection system controller (control unit) Injection sensors Crankshaft position sensor Coolant temperature sensor Throttle position sensor (TPS) Mass air flow sensor Knock Sensor Oxygen concentration sensor (oxygen sensor, lambda probe) Vehicle speed ??sensor Idle control Ignition system Engine control fuses and relays The operation of the injection system Removing the diagnostic pads Replacing injection relays and fuses Removing the control unit and the status indicator of the automobile anti-theft system (APS) Removing the controller Removing the crankshaft position sensor Removing the coolant temperature sensor Removing the throttle position sensor Removing the mass air flow sensor Removing the knock sensor Removing the oxygen sensor Removing the speed sensor Removing the ignition module Cooling system Design description Removing coolant temperature sensor for instrument cluster Removing and checking the thermostat Removing the expansion tank Removing the electric fan Removing the radiator Removing the coolant pump Exhaust system Design description Front pipe removal Removing the optional silencer Neutralizer removal Removing the main silencer Grip Design description Clutch cable removal Replacing drive plate and clutch cover Removing clutch release mechanisms Gearbox Design description Removing the gearshift drive Gearbox removal Replacing gearbox oil seals Gearbox disassembly and assembly Front wheel drive Design description Removing front wheel drives Removing the outer joint Removing and disassembling the inner joint Front suspension Design description Removing the ball joint Removing the lever, brace and bracket Removing the shock absorber strut and its disassembly Removing the anti-roll bar Replacing the front wheel bearing Rear suspension Design description Removing the shock absorber and spring Replacing the silent blocks of the rear suspension beam Removing the rear suspension beam Replacing the hub bearing Steering Design description Steering wheel removal Steering column removal Removing the tie rod end Removing and disassembling the steering gear Brake system Design description Bleeding the brakes Removing the brake master cylinder Removing the vacuum booster and adjusting the brake pedal free play Removing the front brake hose Removing front wheel brake parts Replacing the rear brake cylinder Removing the rear brake hose Checking and adjusting the rear brake pressure regulator actuator Removing the rear brake pressure regulator Removing the parking brake components Electrical equipment Design description Replacing fuses and relays Removing the mounting block Removing the ignition switch Ignition relay removal Battery Generator Generator test Removing and disassembling the generator Starter Starter removal Dismantling of a starter 5712.3708 Dismantling the starter 29.3708 Lighting and light alarm Headlights Removing the headlight, replacing the lamps Headlight hydrocorrector Removing the headlight fluid corrector Fog lights Removing the direction indicator, replacing the lamp Removing the side direction indicator, replacing the lamp Replacing the reversing light switch Removing taillights, replacing bulbs Removing the rear fog lamp relay Removing an additional brake signal Removing the rear license plate light, replacing the lamp Removing the engine compartment lamp holder, replacing the lamp Removing the central interior light and replacing the lamp Removing the front interior light Removing the plafond and the lower glove box lighting switch Removing the steering column switch Removing the alarm switch Sound signal Beeping Cigarette lighter removal Rear window heating system (rear door glass) Window cleaners and washers Removing and disassembling the windshield wiper   Removing the liquid level sensor and the washer electric pump Rear door wiper and washer Removing the tailgate wiper motor gearbox Engine cooling fan motor Monitoring devices and signaling devices Checking control devices and their sensors Removing instrument cluster and light switch Removing the alarm block Body Design description Outside rearview mirror Interior rearview mirror Removing the sun visor Ceiling handrail Facing the tunnel floor Carpeted floor and soundproofing material Removing the shelf under the rear window Roof upholstery Removing the front seat belt Removing the front seat and slide Removing the rear seat Removing the dashboard Removing the inner radiator lining Removing the outer radiator lining Removing the headlamp trim Front bumper with aluminum beam Front bumper with plastic energy absorbing element Rear bumper with aluminum beam Rear bumper with plastic energy absorbing element Fairing removal Removing the hood lock, lock drive and safety hook Hood Mudguard engine Front fender liner removal Front wing Replacing the windshield Replacing an external door lock Removing the door trim Removing the door lock Removing the door glass Removing the power window mechanism Spoiler removal Removing the tailgate trim Removing the tailgate lock Removing the tailgate Removing the tailgate lock Removing the boot lid Heating and ventilation system Design description Heater tap removal Heater fan removal Removing the rear air ducts Removing the instrument panel ducts Removing the heater radiator Removing and disassembling the heater Diagnostics of malfunctions Tuning recommendations Applications A tool used in addition to the staffing Applicable fuels, lubricants and operating fluids Tightening torques for threaded connections Basic data for adjustments and control Lip seals (glands) Rolling bearings Lamps used in the car Electrical equipment schemes

Руководство Haynes по обслуживанию и ремонту автомобиля Pontiac Fiero (1984-1988 гг.).

В данной книге на хорошем инженерном уровне, но в то же время просто и доступно, описаны модели ZAZ-DAEWOO SENS, с 2002 г. выпуска, торговое обозначение: T1311-01, T1311-02. Бензиновый двигатель с системой распределенного впрыска топлива:1. 3 л. - 51.

Учебное пособие предназначается изучающим английский язык и входит в систему предметов, обучающих теории и практике перевода. Материал пособия направлен на освоение и развитие практических навыков перевода с английского языка на русский и наоборот.Основным принципом построения пособия, отбора и расположения учебного материала является создание систематического представления о способах, средствах и приемах преобразования языковых единиц в процессе двустороннего перевода. Пособие может бытьиспользовано в рамках учебного процесса на факультетах иностранных языков, для обучения переводчиков, а также для самостоятельных занятий студентов, аспирантов, преподавателей английского языка и начинающих переводчиков.

Инструкция по ремонту и обслуживанию моделей Fiat Tipo и Tempra. Дано описание всех узлов и агрегатов и советы по их эксплуатации и техобслуживанию. Чертежи, таблицы и схемы электрооборудования. Fiat Tipo - автомобиль итальянской компании Фиат. Был разработан дизайн студией IDEA. Выпускался с 1988 года по 1996 год.

Content

Your BMW 3 series car

• Introduction
• Safety first!
• Troubleshooting an emergency
• Starting the engine from an additional power source
• Wheel replacement
• Towing
• Leak detection
• Weekly checks
• Checks under the hood of the car
• Engine oil level
• Coolant level
• Level of a brake liquid and a working liquid of coupling
• Power steering fluid
• Electrical systems
• Tire condition and air pressure
• Battery
• Working fluids and lubricants

Instruction manual

• Overview of the dashboard, warning lights and devices
• Controls
• Cruise control system
• Air conditioning system with manual control and automatic operation
• Storage bays and other interior components

Regular maintenance and maintenance - gasoline engines

• Introduction
• Regular maintenance
• TO-2
• Resetting maintenance interval (CBS) display mode
• Maintenance of front brakes
• Maintenance of rear brakes
• Car inspection
• Replacement of air filter
• Replacement of spark plugs
• Brake fluid replacement
• Checking and replacing the auxiliary drive belt
• Replacing the fuel filter
• Replacing coolant

Regular maintenance and maintenance - diesel engines

• Introduction
• Regular maintenance
• TO-2
• Resetting maintenance interval (CBS) display mode
• Maintenance of front brakes
• Maintenance of rear brakes
• Car Inspection
• Replacement of the air filter (keys 2/5)
• Replacing the main fuel filter
• Replacing the particulate filter
• Brake fluid replacement
• Checking and replacing the auxiliary drive belt
• Changing the coolant

Procedures for repairing a four-cylinder petrol engine without removing it from the engine compartment

• General information
• Compression check - description and explanation
• Determination of the top dead center for the cylinder 1 piston
• Cylinder head cover - removal and installation
• Torsion damper / pulley and crankshaft pulley hub - removal and installation
• Chains of drive timing - removal, inspection and installation
• Asterisks and timing chain tensioner - removal and installation
• Phase Shifter - description and replacement of components
• Camshafts and pushers
• Cylinder head - removal and installation
• Crankcase - removal and installation
• Front frame reinforcement - removal and installation
• Front subframe - lowering, removal and installation
• Balancing shafts - general information
• Oil pump - removal, inspection and installation
• Oil seals - replacement
• Handwheel / drive clutch plate - Removing and installing
• Centering Crankshaft Bearing - Replacement
• Engine / gearbox mountings - check and replace
• Engine oil level and pressure sensors

Procedures for repairing a six-cylinder petrol engine without removing it from the engine compartment

• General information
• Compression check - description and explanation
• Determination of the top dead center for the cylinder 1 piston
• Cylinder head cover - removal and installation
• Torsional vibration damper - removal and installation
• Chain of drive timing - removal, inspection and installation
• Components of the valve timing system (Vanos) - removal, inspection and installation
• Camshafts and pushers
• Components of the Valvetronic system - removal and installation
• Cylinder head - removal and installation
• Crankcase - removal and installation
• Oil pump - removal, inspection and installation
• Oil seals - replacement
• Handwheel / drive clutch plate - removing and installing
• Engine / gearbox mountings - flywheel guide bearing - check, remove and install
• Engine oil level and pressure sensors

Repair procedures for the diesel engine (M47T2 and M57T2) without removing it from the engine compartment

• General information
• Compression check - description and explanation
• Engine assembly / valve timing - general information and usage
• Cylinder head cover - removal and installation
• Crankshaft pulley / torsional vibration damper - Removing and installing
• Camshafts, rocker arms and hydraulic lifters - removal, inspection and installation
• Cylinder head - removal and installation
• Crankcase - removal and installation
• Oil pump - removal, inspection and installation
• Balancing shaft assembly - removal and installation
• Oil cooler - removal and installation
• Crankshaft oil seals - replacement
• Handwheel / drive clutch plate - Removing and installing
• Engine supports - checking and replacing
• Flywheel guide bearing - check, remove and install
• Chains for timing and cover - removal and installation
• Engine oil level and pressure sensors

Repair procedures for the diesel engine (N47 and N57) without removing it from the engine compartment

• General information
• Compression check - description and explanation
• Engine assembly / valve timing - general information and usage
• Cylinder head cover - removal and installation
• Crankshaft pulley / torsional vibration damper - removing and installing
• Camshafts, rocker arms and hydraulic lifters - removal, inspection and installation
• Cylinder head - removal and installation
• Crankcase - removal and installation
• Oil pump / vacuum pump - removal, inspection and installation
• Balancer shaft assembly - general information
• Oil cooler - removal and installation
• Crankshaft oil seals - replacement
• Handwheel / drive clutch plate - Removing and installing
• Engine supports - checking and replacing
• Flywheel guide bearing - check, remove and install
• Chains of drive timing and cover - general information
• Engine oil level and pressure sensors

Removing the engine from the engine compartment and the overhaul procedure

• General information
• Major engine repairs - general information
• Engine removal - methods and precautions
• Engine - removal and installation
• Engine overhauling - sequence of disassembly
• Cylinder head - disassembly
• Cylinder head and valves - cleaning and checking
• Cylinder head - assembly
• Piston / connecting rod assembly - removal
• Timing drive chain (diesel engines N47 and N57) - removal and installation
• Crankshaft removal
• Cylinder block / crankcase - cleaning and inspection
• Piston / connecting rod assembly - check
• Crankshaft check
• The crankshaft bearing and thrust bearing - check
• Overhauling - assembly sequence
• Piston rings - installation
• Crankshaft - installation
• Pistons / connecting rods in assembly - installation
• Engine - operation after major repairs

Cooling system, heater and ventilation system

• General information and precautions
• Cooling hoses - detach and replace
• Radiator - removal, inspection and installation
• Thermostat - removal and installation
• Cooling fan and viscous coupling - removal and installation
• Electric cooling fan and casing - Removing and installing
• Electrical sensors for the cooling system - checking, removing and installing
• Water pump - removal and installation
• Heater and ventilation system - general information
• Components of the heater / ventilation system - removal and installation
• Air conditioning system - general information and precautions
• Components of the air conditioning system - removal and installation
• Heating element for auxiliary heater - removal and installation
• Shutters and servomotor for adjusting the intensity of the radiator airflow - removal and installation

The power supply and exhaust system - gasoline engines

• General information and precautions
• Air filter assembly - removing and installing
• Fuel tank - removal and installation
• Accelerator pedal - removal and installation
• Fuel injection system - general information
• Fuel injection system - pressure relief and refueling
• Fuel pump / fuel level sensors - Removing and installing
• Fuel injection system - check and adjustment
• Throttle body - removing and installing
• Components of the distributed fuel injection system - removal and installation
• Collectors - removal and installation

Exhaust system - removal and installation

• Power and exhaust system - diesel engines General information and precautions
• Air filter assembly - removing and installing
• Fuel tank - removal and installation
• Accelerator pedal - removal and installation
• Fuel injection system - general information
• Fuel injection system - pressure relief and refueling
• Fuel pump / fuel level sensors and control unit - removal and installation
• Fuel injection system - check and adjustment
• High-pressure fuel pump (fuel pump) - Removing and installing
• Fuel injectors - removal and installation
• Components of the electronic engine management (EDC) - removal and installation
• Turbocharger - description and precautions
• Turbocharger - removal and installation
• Turbocharger - check and overhaul
• Intercooler - removing and installing
• Collectors - removal and installation
• Exhaust system - general information and replacement

Control systems for harmful emissions

• General Information
• Emission control systems (gasoline engines) - checking and replacing components
• Emission control systems (diesel engines) - checking and replacing components
• Catalytic converter - general information and precautions

Starting and recharging systems

• General information and precautions
• Detection of malfunctions in the electrical system - general information
• Battery - check and charge
• Storage battery - detachment, removal and installation
• Charge system - check
• Generator drive belt - removal, installation and tension
• Generator - removal and installation
• Generator - check and overhaul
• Startup system - check
• Starter - removal and installation
• Starter - check and overhaul
• Preheating system for diesel engines - description and verification
• Glow plugs - removal, inspection and installation
• Control unit / relay for pre- and post-heating systems - removal and installation

Ignition system

• General information and precautions
• Ignition system - check
• High-voltage ignition coils - removal and installation
• Detonation sensor - removal and installation

Clutch

• General information
• Clutch assembly - removal, inspection and installation
• Clutch release bearing and lever - removal, inspection and installation
• The working cylinder - removal, check and installation
• Master cylinder - removal, inspection and installation
• Hydraulic clutch circuit - pumping
• Clutch pedal - removal and installation

Manual transmission

• General information
• Checking the transmission oil level
• Replacing gearbox oil
• Components of the gearshift mechanism - removal and installation
• Oil seals - replacement
• Switch for reversing lights - check, remove and install
• Manual gearbox - Removing and installing
• Major overhaul of a manual transmission - general information

Automatic transmission

• General information
• Selector lever - removal and installation
• Cable of the selector lever - removal, installation and adjustment
• Oil seals - replacement
• Automatic gearbox - removal and installation
• Overhaul of an automatic transmission - general information
• Electronic components / sensors - removal and installation
• Checking the automatic transmission fluid level
• Automatic transmission replacement

Main drive, drive shafts and driveshaft

• General information
• The main gear assembly is removal and installation
• Seals of the final drive assembly - replacement
• Drive shafts - removal and installation
• Anthers of drive shafts - replacement
• Drive shaft - removal and installation
• Rubber coupling propshaft - check and replace
• PTO shaft bearing - checking and replacing
• Universal joints of the propshaft - check and replace
• Checking the final drive oil level

Brake system

• General information
• Hydraulic system - air removal
• Hydraulic connections and hoses - replacement
• Front brake pads are replacement
• Rear brake pads - replacement
• Front brake disc - check, remove and install
• Rear brake disc - check, remove and install
• Front brake caliper - removal, overhaul and installation
• Rear brake caliper - removal, overhaul and installation
• Master brake cylinder - removal, overhaul and installation
• Brake pedal - removal and installation
• Vacuum brake booster - checking
• The check valve of the vacuum amplifier of brakes - removal, check and installation
• Parking brake - adjustment
• Parking brake lever - removal and installation
• Parking brake cables - removal and installation
• Parking brake shoes - removal and installation
• Stop light switch - removal and installation
• Anti-lock braking system (ABS) - general information
• Anti-lock components - removal and installation
• Vacuum pump - removal and installation

Suspension and steering

• General Information
• Front hub assembly - removal and installation
• Front tail-vise of swivel pin - removal and installation
• Front pillar - removal, overhaul and installation
• Front levers / rack - removal, overhaul and installation
• Ball joint for front lever - replacement
• Front anti-roll bar - removal and installation
• Connecting rod of the stabilizer of cross-section stability - removal and installation
• Rear hub assembly - replacement
• Rear hub bearing replacement
• Rear shock absorber - removal, overhaul and installation
• Rear helical spring - removal and installation
• Shaft of rear swivel pin - removal, overhaul and installation
• Rear levers / racks - removal, overhaul and installation
• Rear anti-roll bar - removal and installation
• Steering wheel - removal and installation
• Steering column - removal, inspection and installation
• The mechanism for locking the steering column - general information
• Intermediate shaft of the steering column - removal and installation
• Rack-and-pinion steering gear assembly - removal, overhaul and installation
• Power steering pump - removal and installation
• Hydraulic power steering circuit - pumping
• Active Steering control unit - removal and installation
• Rubber anthers of the steering rack - replacement
• Tips of transverse steering rods / ball joints - removal and installation
• The cross-section steering draft - replacement
• Dynamic stability control (dsc) - general information and component replacement)
• Wheel alignment angles - general information

Body structure and components

• General information
• Maintenance - body and frame
• Maintenance - upholstery and rugs
• Elimination of minor body damage - repairs
• Removing serious body damage - general information
• Front bumper - removal and installation
• Rear bumper - removal and installation
• Hood - removal, installation and adjustment
• Hood opening cable - removal and installation
• Hood lock - removal and installation
• Doors - removal, installation and adjustment
• Internal door trim panels - removal and installation
• Handle and door lock components - removal and installation
• Glass lifters and regulator - removal and installation
• Lid / tailgate and support pillars - Removing and installing
• Components of the lid / tailgate lock - removal and installation
• Components of the central lock - removal and installation
• Components of electric glass lifts - removal and installation
• Mirrors and related components - removal and installation
• Windshield and rear window - general information
• Hatch - general information, servo replacement and initialization
• Exterior elements of the body - removal and installation
• Seats - removal and installation
• System of pretensioners of seat belts - general information
• Safety belt components - removal and installation
• Internal cladding panels - removal and installation
• Central console - removal and installation
• Fixing panel assembly - removal and installation

Electrical equipment and electrical systems

• General Information
• Detection of malfunctions in the electrical system - general information
• Fuses and relays - general information
• Switches - removal and installation
• Lamps (external lighting) - replacement
• Lamps (interior lighting) - replacement
• External headlamps - removal and installation
• Adjusting the height of the headlights - general information
• Dashboard - removal and installation
• Components of the instrument panel - removal and installation
• Rain sensor - removal and installation
• Suspension height sensor - removing and installing
• Tire pressure monitoring system indicator - general information
• Acoustic signal - removal and installation
• Wiper arm - removal and installation
• Draft and wiper drive - removal and installation
• Components of the windshield washer system / headlights - removal and installation
• Audio system unit - removal and installation
• Speakers - removal and installation
• Radio antenna - general information
• Cruise control system - general information and component replacement
• Anti-theft system - general information
• Components of the heated front seats - removal and installation
• Airbag System - General Information and Precautions
• Components of the airbag system - removal and installation
• Parking assist system (PDC) - general information and component replacement
• Electrical diagrams - general information

Applications

• Dimensions and weight
• Vehicle identification numbers
• General repair procedures
• Lifting the car with a jack, the points of the pillars
• Tools and devices
• Checking the technical condition of the car
• Troubleshooting